Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN50110-TV | 50 | 110 | 82 | 53.5 | – | – | 25 |
| 95 | – | – | 17.5 | – | – | 0.3 | 0.6 |
|
| 96 | 75 | 172,000 | 480,000 | 42,000 | 90,000 | 3,100 | 1,100 | 3.8 | 4,600 | 2,900 | 29.8 | 1 | 3.3 |
| ZARN50110-L-TV | 50 | 110 | – | – | 103 | 74.5 | 25 |
| 95 | 75 | 93 | 17.5 | 38.5 | 14 | 0.3 | 0.6 |
|
| 96 | 73 | 172,000 | 480,000 | 42,000 | 90,000 | 3,100 | 1,100 | 3.8 | 4,600 | 2,900 | 35.3 | 1 | 3.75 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
China Factory 1.5 Ton Mini Digger Bagger Pilot Operation 1500kg Ht15 PRO Small Crawler Excavator
>>
Rare Earth powder cerium oxide Lanthanum oxide powder with good price
>>
Wholesale Price Best Horse Riding Helmets Supplier Rider Equestrain Men Women
>>
Radio Shuttle Car Automated Retrieval Racking System for Warehouse Storage
>>
Tubeless Snap In Chrome Sleeve Colorful Rubber Tire Valve Stem TR413AC TR414AC
>>
CNC Precision Surface Grinding Machine Psg-306wms3 Flat Grinder Saddle Type Three-Axis Automatic Series
>>
Performance Racing Suspension Swage Steel Tube Radius Rods
>>
8K Fiber Optic HDMI Cable 30 Feet, 18gbps 4K 60Hz (4: 4: 4 HDR10 HDCP2.2) 1440p 144Hz High Speed Ultra HD One-Direction Cord
>>
Eco-friendly pp waterproof disposable coverall ppe overall
>>
New Cute Dinosaur Three-Piece Set Paper Plate Paper Cup Paper Towel Set Birthday Party Supplies Tableware Set
>>
Air Freight Shipping From China to All Over of The World Fob/CIF/DDU/DDP Door to Door Delivery
>>
31250-b2040 Daihatsu Clutch Disc for cars
>>
440GSM Acid Wash French Terry Pure Cotton Soft Wear High Quality Plain Design Custom Logo Shorts for Men
>>
VYKON NPB-PWR in stock
>>
New Multi Color Change Car Offroad RGB LED Light Bar
>>
Hot Sale Trunk Vibrator Fruit Tree Vibrating Harvester Hydraulic Vibrating Fruit Shaker
>>
Hot Selling Reloj De Mujer Damen Uhr Woman Quartz Watches Low MOQ Designer Rose Gold Stainless Steel Orologio Donna Ladies Watch
>>
Chaff Cutter Machine Electric Chaff Cutter for Sale Grass Chopper Machine for Animals Feed
>>
Wiiboox High Precision Rapid Prototyping 3D Desktop LCD Printer
>>
S/M/L/XL Medical PVC Supply Nebulizer Mask for Single Use
