Product Details
Product Description
Product Description
Focus on DCS, PLC, robot control system and large servo system.
Main products: various modules / cards, controllers, touch screens, servo drivers.
Advantages: supply of imported original products, professional production parts,
Fast delivery, accurate delivery time,
The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands
8.8 5704 Fire Card The 5704F fire input circuit operates from the system dc input supply (21 to 32V) but has a built-in voltage limiter that limits the maximum loop voltage to +24V to protect the detectors from damage. When the system supply is less than +24V the limiter has no effect and the loop will see the true input supply voltage. The loop current is determined by measuring the voltage across a 220 ohm current sense resistance. A link selectable 330 ohm barrier equivalent resistance is incorporated for use when an external IS barrier is NOT fitted. For fault monitoring purposes, an end of line (EOL) resistor must be fitted in or after the last detector on the loop. The typical value for the end of line resistance is 5.1k ohms although this may need to be reduced when many detectors are fitted onto the loop. An equivalent circuit of one fire input together with an example detector connection is shown below:- 8.8.1 Line Resistance Detectors should be located such that the line resistance of the cable required does not prevent correct operation. As a general guide and for a typical installation of twenty low quiescent current detectors, the loop cable resistance should be kept below 100 ohms total (50 ohms per core). The table below gives a quick guide to the maximum cable lengths permitted in this case: Maximum Cable Length (m) Detectors Conductor Cross Sectional Area AWG 21 19 18 16 14 mm2 0.50 0.75 1.00 1.50 2.50 20 low quiescent (100µA) detectors 1300 2000 2700 4100 6500 For further details of line resistance calculation refer to the 5704F Fire Card manual 05704- M-5002. 14 System 57 Quick Start Guide 05701-M-5026 MAN0839 Issue 1 8.8.2 Typical Loop Powered Detector Connections Loop powered detectors (e.g. most smoke, heat and manual call points) have two wire connection. The detector documentation will indicate the positive and negative loop connections. Multiple detectors may be connected in parallel on a single loop input provided the loop operational limit for quiescent current is not exceeded. At the System 57 end of the field cables, the two detector wires should be connected to the appropriate channels IN+ and IN- terminals of the Hex Relay Interface Card that is attached to the required 5704F Control Card. The loop current always flows from the IN+ terminal and returns via the IN- terminal. For fault monitoring purposes an end of line (EOL) resistor must be fitted in or after the last detector on the loop. The typical value for end of line resistance is 5.1k ohms. The detector cable screen, or steel wire armour or braid as appropriate, should be connected to the system protective earth. This can be achieved where the cable enters the cabinet by using a metal cable gland, or by other suitable means, and avoiding any screen tails within the cabinet. Where the cable consists of a separate screen sheath and wire armour or braid, the armour should be connected at the cabinet entry to the protective earth and the screen sheath should be connected to the GROUND terminal of the Hex Relay Interface Card or to a suitable instrument earth point. EOL 5.1k - + IN- - + 23 21 Detectors IN+ 5704 Hex Card The diagram shows the detector connections for C
h
>>
Hot sale outdoor industrial white 13 gallon trash can with lid
>>
Factory Customized High Purity Quartz Glass Tube High Temperature Heating Tube Furnace Tube
>>
11oz Cotton Star Dot Jacquard Denim Selvage Jeans Fabric for Women's dress 32/33“
>>
Electric Loading Alloy Steel Rockwell Hardness Tester Motorized Rockwell Hardness Testing Machine for Metal
>>
Tr-150 Office Equipment, Binding Machine, Punch Machine, Office Supply
>>
High Precision Wafer Grinding Thinning Machine
>>
Outdo Motorcycle Battery Ytx4l-BS Lithium Batteries for ATV, UTV
>>
Shantou Bote Bt-F12 1500W Tube CNC Laser Metal Cutting Machine with CE ISO
>>
Timing Chain Kit for Ford Transit 2.4L OE BK3Q6268AA 4C1Q6K261BA TK4590
>>
Factory Fabric Wholesale OEKOTEX-100 Sustainable 100 Bamboo Fiber Fabric for Textile
>>
Portable Cheap 1.5m1.7m 1.9m 2.1m 3m Foldable Casting Fishing Net Long Handle Telescopic Landing Fishing Net
>>
High quality electrical socket/ switch socket packing machine with hanging hole
>>
LIVTER Saw Blade Fine Tooth Cutting Blade Acrylic Plexiglass Special Alloy Saw Blade
>>
OEM Sanwan Taps Garden Hose Forged Brass Ball Taps as-Bb001
>>
Luxury and Elegant Look Consistent Grain Chrome Tanned Cow Genuine Leather from Trusted Exporter
>>
Anti Static Disposable Smock Non-Woven
>>
Dongfeng 5 square and 10 square four-wheel drive (all wheel drive) sprinkler can be registered nationwide
>>
Heavy Duty Horizontal Metal Turning Lathe Conventional Lathe Machine Cw6180 in Manual Type
>>
10KG Original Factory Stainless Steel Laundry Washer Dryers Washing Machines
>>
Custom Decorative 3-ply Non-medical Disposable Face Masks w/ Elastic
