Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN70130-TV | 70 | 130 | 82 | 53.5 | – | – | 25 |
| 115 | – | – | 17.5 | – | – | 0.3 | 0.6 |
|
| 116 | 100 | 201,000 | 630,000 | 56,000 | 119,000 | 2,400 | 800 | 4.8 | 5,800 | 6,000 | 62.2 | 1 | 4.1 |
| ZARN70130-L-TV | 70 | 130 | – | – | 103 | 74.5 | 25 |
| 115 | 100 | 115 | 17.5 | 38.5 | 16 | 0.3 | 0.6 |
|
| 116 | 98 | 201,000 | 630,000 | 56,000 | 119,000 | 2,400 | 800 | 4.8 | 5,800 | 6,000 | 77.3 | 1 | 4.85 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Outdoor Play Science and Education Toys Kids Wooden Binoculars with Lenses
>>
Equipped with Emergency Stop Foot Brake Reliable Performance Electric Servo-Driven Press Brake
>>
High Speed 15m 18Gbps HDTV 2.0 cord 4K 60Hz Displayport To Multimedia Interface Adapter Cable 2160P 1080P Ethernet HDTV Cable
>>
Dual Remote Control 360 Degrees Remote Control Car with Spray, Gesture Watch Car Toy, Gesture RC Stunt Car with Lights & Music Toy
>>
High Quality Windproof Aluminum S Shaped Perforated Strip Panel Ceiling
>>
0335s-D3/D4 One Piece Computer Heavy Duty Industrial Sewing Machine
>>
3t Yellow Polyester Material Webbing Sling Belt
>>
3 / 5 gallon Bottle Washer Machine Barrel Rinser with Inner Brush
>>
China skid loader road sweeper broom
>>
Stranded Aluminum Wire for Communication Cable
>>
Wholesale Nonwoven Drawstring Bag Shoes Dust Bags
>>
Dental Model Showing The Sealant of Occlusal
>>
High Speed Forging Train Bogie Wheel
>>
Best Factory Sale Electric Animal Cow Chicken Poultry Feed Making Machine for Pelletizing Manufacturing, Broiler, Cattle
>>
Meklon Car Paint Spray Coating Meiguanda Acrylic Adhesive Tape
>>
China Xuzhou Manufacture Crawler Excavator Xe690dk 65t Mini Crawler Excavator
>>
Hbs Electric DOT Pin Marking Machine for Metal
>>
Durable Excavator Grab for Efficient Steel Scrap and Machinery Handling
>>
Residual Current /Vacuum Circuit Breaker/Miniature Circuit Breaker/Mini Circuit Breaker/ RCCB ELCB MCCB 6ka 10 Ka 12.5~125A Moulded Case Circuit Breaker
>>
High Density 6201-2rz 12*32*10mm Rodamiento Single Row Deep Groove Ball Bearing for Truck
