Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque MRL Nm | Rigidity axial caL N/µm | Tilting rigidity ckL Nm/ mrad | Mass moment of inertia3) Mm kg · cm2 | Axial runout6) µm | Mass m =kg |
| axial | radial |
Da max. | da min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r min. | r1 min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN2062-TV | 20 | 62 | 60 | 40 | – | – | 20 |
| 52 | – | – | 12.5 | – | – | 0.3 | 0.6 |
|
| 53 | 38 | 64,000 | 141,000 | 22,600 | 36,000 | 6,000 | 1,500 | 1.3 | 2,300 | 400 | 1.98 | 1 | 0.87 |
| ZARN2062-L-TV | 20 | 62 | – | – | 75 | 55 | 20 |
| 52 | 40 | 50 | 12.5 | 27.5 | 11 | 0.3 | 0.6 |
|
| 53 | 38 | 64,000 | 141,000 | 22,600 | 36,000 | 6,000 | 1,500 | 1.3 | 2,300 | 400 | 2.27 | 1 | 0.99 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
20-50 Micron Mettallized and Glossy White Tc Pet Film for Tyre / Tire Labels
>>
Wall Mount LED Light Box for Shop Name
>>
A2710503347 camshaft gear for Benz C250 W204
>>
ZARN2062-TV 20*62*60mm Needle roller/axial cylindrical roller bearings
>>
Memory Foam Luxury Car Mat Center Seat Armrest Cushion Pillow Support Pad Interior Trim
>>
Rubber Flexo Plate Making Machine Solvent Washing Flexo Printing Plate Making Machine
>>
Small Radial Drilling Machine Z3032X7 Z3032X7p High Quality China Radial Arm Drilling Machine
>>
CNC Router Atc 1325 Wood Carving Machine Automatic
>>
Hight Quality Natural Latex Pillow 100% Hypoallergenic Latex Pillow
>>
Positive And Negative Screw Connection Connecting Sleeve Stainless Sleeve
>>
Customized 1.68m 2PCS Fishing Rod and Reel Combo Kids Fishing Pole Set for Christmas
>>
Strapless Draped Satin Ball Gown High Slit Wedding Dress Bridal Wear
>>
Factory supply stainless steel Potato tomato vegetable Garlic grading sorting machine Apple Grading Machine
>>
1kHz-50kHz Sample Rate Mineral Blast Vibration Test/Sam-20 Blasting Vibration Monitor
>>
High Speed Spindle Veneer Peeling Machine 8FT Spindle Less Veneer Peeling Machine Wxq2700-450
>>
Newest and Funny Handmade Ceramic Photo Frames Sea Designs
>>
8t Capacity Webbing Sling for Industrial and Construction Use
>>
Yc Diesel Engine 100kw 125kVA 3phase electric Diesel Genset Power Generator
>>
Factory Direct Decorative Sky Starry LED Pendant Lamps
>>
A3501 Android 8.1 3.5 Inch Touch Screen 4G LTE Mobile Phones with WiFi Whatsapp Support Bar Design and Android Keypad