Welcome to visit

Design Rules Textbook for Plastic Injection Mold Design

US$1.00 1 Piece (MOQ)

Basic Info.

Model NO.
Fl-26
Shaping Mode
Extrusion Mould
Surface Finish Process
Heat Treatment
Mould Cavity
Multi Cavity
Plastic Material
ABS
Process Combination Type
Single-Process Mode
Application
Car
Runner
Cold Runner
Design Software
PRO-E
Installation
Fixed
Certification
ISO
Standard
Misumi
Customized
Customized
OEM
Yes
Transport Package
Box
Specification
TBA
Trademark
Flying Eagle
Origin
China
HS Code
39231000
Production Capacity
500PCS/Year

Product Description

Overview
Runner design dictates part quality and productivity. The design rules that follow provide
general guidelines for runner design.
Runner size
Runner cross section
The cross-sectional area of a runner should not be smaller than that of the sprue, to permit rapid,
unaltered flow of the material to the gating area.
Cold runner diameter
The selection of a cold runner diameter should be based on standard machine tool cutter sizes. The
minimum recommended runner diameter for most materials is 1.5 mm (0.06 inches). Typical runner
diameters for various unfilled generic materials are shown in Typical runner diameters for unfilled
generic materials.
See Determining runner dimensions for more information on this topic.
Trapezoidal runners
The depth of a trapezoidal runner is approximately equal to its width, with a 5º to 15º draft (taper)
on each side wall.
Scrap
Use a small runner size to minimize scrap volume.
Raising melt temperature
Smaller runner size is preferred over larger runner size in order to generate viscous (frictional)
heating. Viscous heating generated in the runner system is an effective way to raise the melt
temperature instead of using a high barrel temperature, which is likely to cause material
degradation.
Branched runners
Each time a runner is branched, the diameter of the branch runners should be smaller than the main
runner, because less material flows through the branches and it is economically desirable to use
minimum material in the runners.
Where N is the number of branches, the relationship between the main runner diameter (dmain) and
the branch runner diameter (dbranch) is
Runner intersections
All runner intersections should have a cold solid slug well to help the flow of material through the
runner system and into the cavity. the diagram below shows that the length of the well is usually
equal to the runner diameter.
FIGURE 1. The cold slug well is typically an extension of the runner at an intersection with another runner.
Hot runners
When designing Hot runner systems, it is necessary to consult suppliers for availability of the proper
manifold and drops.
Easy ejection
Runner design must provide for easy ejection and easy removal from the molded part, with proper
cross-sectional and draft angle. For most materials, the runner surface must be polished to facilitate
flow and part ejection. Extended runner systems should have multiple sprue pullers and ejection
locations.
>> EMS Foot Massagerclassic Comfortable Shiatsu Pain Relieve Full Wrap Luxury Vibration Leg and Foot Massager
>> New Fully Automatic 9590 Cup Type Shaped Mask Making Machine KN95 Grade Protective Mask Making Machine
>> High gloss finished wooden pocket watch box with Mapa paper watch storage box with bottom drawer watch box
>> Wholesale high quality Auto parts 12637199 12673527 12683541 12686362 Spark Plug 1.5 T For Buick Chevrolet 41-124
>> Design Rules Textbook for Plastic Injection Mold Design
>> larch lvl beam, russian larch beam, lvl timber
>> Fat Removal 980nm 1470nm Diode Laser Lipolisis Vaser Liposuction Endolaser Lift Machine
>> 5 Layers 6 Layers 7 Layers High Quality Pneumatic Rubber Marine Airbag
>> European Styles UPVC Windows Manufacturer PVC Sliding Window Modern Sliding European
>> Large Space Luxury Sliding Door Water Preventing Plates Stainless Steel Pet Dog Drooming BathTub
>> steam-type harmless treatment equipment - manufacturer of harmless treatment equipment for dead and sick poultry
>> PU Thermal Conductive Structural Sealant for structural bonding between power battery cells
>> Custom CNC Machining Services for Aluminum Brass Stainless Steel
>> Factory Outlet High Speed Chicken Fish Beef Ball Forming Machine Meatball Maker
>> High Quality Decorative Wood Wall Decor for Living Room W18A172
>> JINGHONG Factory Outlet Durable 50ton Crane Chain Hook and Slip with Safety Latch
>> Customized White Acetal Plastic POM Polyacetal Rod
>> CNC Machining High Precision Turning Custom Fabrication Diverse Aluminium Titanium Nylon Copper
>> Plastic Injection Blowing Molding Machine Pet Sanitizer Bottle Disinfectant Medicine Pharmacy Tablet Container One Stage Injection Stretch Blow Mouding Machine
>> gearbox parts double H operating device housing valve F96194-C F96194-15 F96194-9 F96194-8C