ZARN60120-L-TV 60*120*82mm Needle roller/axial cylindrical roller bearings

Product Details

Product Description

Product Description

Designation	Dimensions																		Mounting dimensions		Basic load ratings				Limiting speeds		Bearing frictional torque MRL Nm	Rigidity axial caL N/µm	Tilting rigidity ckL Nm/ mrad	Mass moment of inertia3) Mm kg · cm2	Axial runout6) µm	Mass m =kg
																					axial		radial
																			Da max.	da min.	dyn.Ca	stat. C0a	dyn.Cr	stat. C0r	nG oil	nG grease
	d	D	H	H1	H2	H3	C	C1	D1	D2	D3	B	B1	B2	r min.	r1 min.	d1	J			N	N	N	N	min–1	min–1
ZARN60120-TV	60	120	82	53.5	–	–	25		105	–	–	17.5	–	–	0.3	0.6			106	90	187,000	550,000	44,500	92,000	2,700	950	4.2	5,300	4,300	43.8	1	3.7
ZARN60120-L-TV	60	120	–	–	103	74.5	25		105	90	105	17.5	38.5	16	0.3	0.6			106	88	187,000	550,000	44,500	92,000	2,700	950	4.2	5,300	4,300	54.5	1	4.85

Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs

---

>> CNC Corner cleaning machine for pvc window and door
>> yuling China- Europe international Eastbound Block train
>> Basketball Dribble Trainer Warm up Basketball Training Agility Training Pole
>> Cheap 350ml 500ml 600ml 750ml 1000ml Disposable Medical Dispoz-a-bag Urine Collection Bag Urine Leg Bag For Leg
>> LED glass lens module light source projection light 50W module high pole light M4G5 street light module M212 tunnel light magnolia light LED module
>> Household Mobile Clothes Hanger Multi Pole Folding Clothes Hanger
>> Living Room Kitchen Home Office Wood Shower Corner Shelf Bamboo Towel Rack Storage Shelf Wooden Bamboo Bathroom Shelf
>> BACKBONE SPOON fast jig fishing spoon lures saltwater spinner bait lure casting fishing lure
>> High Quality 1.37mx50m PVC Table Cloth Cover in Piece or by Roll for Table Cover
>> Moringa seed sheller
>> Wall Mount Acrylic Sign Holder Display Frame for Office Restaurant Paper Document
>> Injection Molding Machine Hxm658-II for The Production of Pipes
>> Semi Automatic Advanced Tape Machine Double-Sided Tape Machine Improves Efficiency and Productivity
>> 2024 Electric Chain Hoist 5ton 6m with High Strength Lifting Chain
>> Farm Equipment Disc Harrow Heavy Duty Offset Hydraulic Disc Harrow for Tractors Hot Sale in Iraq
>> Expandable Stainless Steel Large Over The Sink Kitchen Organers Counter Dish Drainer Drying Rack with Black Removable Holder
>> 40A New Energy Charging Station Power Plug 4.0 Crown Spring Pin Socket Male and Female Copper Pins
>> ISO9001: 2015 Factory Supply of Electric Bike for Adults/60V/72V Two Wheel Scooters Electric Bicicleta with Pedal Speed >50km/H/OEM/ODM
>> PS Plastic Recycling Machine PP PE with Low Price
>> 4 Axis DSP/Ncstudio/Mach3 Z Axis 400mm Height 1325 1530 Stone Carving Engraving Machine Stone CNC Router with Rotary for Marble Granite Glass