Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARF65155-TV | 65 | 155 | 82 | 51 | – | – | 22.5 | 12.5 | 110 | – | – | 17.5 | – | – | 0.3 | 0.6 | 6 | 128 | 111 | 97 | 172,000 | 500,000 | 54,000 | 104,000 | 2,600 | 900 | 4 | 4,800 | 4,000 | 51 | 1 | 5.1 |
| ZARF65155-L-TV | 65 | 155 | – | – | 103 | 72 | 22.5 | 12.5 | 110 | 90 | 108 | 17.5 | 38.5 | 16 | 0.3 | 0.6 | 6 | 128 | 111 | 88 | 172,000 | 500,000 | 54,000 | 104,000 | 2,600 | 900 | 4 | 4,800 | 4,000 | 60.1 | 1 | 5.7 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
High Performance Z3050X16 Radial Drilling Machine for Metal Projects
>>
Factory Outlet Good Quality Hot Press Machine for Laminate Flooring Boards
>>
9 Shelf wood display stand flowers rack for garden
>>
Roll to Sheet Cutting Machine Sheeter with 6 Unwind Stands 1400mm Cutter
>>
304 316L Compression Stainless Steel Water Pipe Seamless Thin Wall Hollow DN100 DN65 Factory Hospital Use ASTM Standar
>>
2022 Factory Supply Tabletop Baking Round Under Floor Nonstick Mesh BBQ Grill Mat
>>
New Design Handbag Embellished Structured Fashioin Shoulder Bag PU Leather Bag
>>
Smiger Affordable Portable Digital Piano
>>
14m High Reach Crawler Hydraulic Scissor Lift for Extended Use
>>
New Type 2 in 1Car Windshield Suction Cup 360 Mobile Phone Holder Mobile Phone Accessories Holder
>>
Hydraulic Surface Grinding Machine (MY1230) Surface Grinder Machine Price
>>
persian pistachio pistache phistachios pistazien candied pistachios
>>
Professional Manufacturer Granite Limestone Crushing Stone Aggregate Cone Crusher for Mineral Processing
>>
HC71913-C-T-P4S Ultra-precision Angular Contact Ball Bearings
>>
Animal Feed Cooling Equipment Chicken Feed Cooler
>>
Dried Fruit And Nuts Cucumber Slice Cut Shred Cube Cutter Vegetable Dicer Dice Machine
>>
XCMG Road Roller Pump 803072822 Water Pump 803202971
>>
Rainbow Colorful Gradient Double Sided Satin Ribbon for DIY Wedding Party Gift Wrapping
>>
Desktop Laser on Plastic Bottle /Battery/Matel Best Laser Etching Machine
>>
Sports Soccer Jacquard Scarf Fan Muffler with Customized Logo
