Product Details
Product Description
Product Description
Brand: METSO
Type:IOP303
Origin: the United States
Warranty: 365 days
Colour: new/used
Shipping method: Courier delivery
SPECIFIC CAUTIONS (continued) Page 114: It is not possible to change the CI852 unit via hot swap and it is not allowed to perform an online upgrade of firmware in a system containing CI852. Page 118: Hot swap is supported for CI854A (not CI854). Page 133: – 115 V for 110–120 V AC – 230 V for 220–240 V AC (default position on delivery). Page 141: To avoid error indications from SA/SB when single power supply is used, it is recommended to connect the input terminals SA/SB on the CPU to +24 V, see Figure 47. Page 143: Do not connect the TK821V020 cable until the AC 800M Controller has been powered-up normally and the memory back-up function has been activated, that is, the B(attery) LED flashes. If no normal power supply is connected to the PM8xx processor unit, the CPU memory will immediately start to consume battery power when the cable is connected. Page 157: When setting the IP address of the primary CPU in Control Builder, the backup CPU must be turned off (powered down). Otherwise the backup CPU will take over and you get disconnected. Page 159: Note that the electrical ModuleBus can only be used for connection of S800 I/O when AC 800M is running in single CPU configuration. Page 184: Note that a Backup CPU with severe communication errors on the ModuleBus will be rejected (if ModuleBus is part of the HW configuration) and synchronized state will never be reached as long as error remains. Page 189: The RCU Link Cable must NEVER be removed from the primary Processor Unit during redundant operation. Removal of the cable may cause the unit to stop. Page 192: Due to the batteries being connected in parallel, it is necessary, when using the SB821 external battery, to remove the internal battery from the PM8xx in order to avoid reducing available memory back-up time.
SPECIFIC CAUTIONS (continued Page 195: Due to the batteries being connected in parallel, it is necessary, when using the SB821 external battery, to remove the internal battery from the processor unit in order to avoid reducing available memory back-up time. -200 and Page 201: Reuse of CPU modules replaced from redundant configurations within the same control network, might cause control network problems due to the MAC and IP address handling. See MAC and IP Address Handling in Redundant Configuration on page 49. Such reuse should not be fulfilled unless both the replaced module and the module previously acting together with it in redundant configuration are known to be restored from the previous mutual address swap. It is recommended to set up an IP-config session and use the “Restore factory settings” option subsequently followed by reassignment of the IP address or assignment of a new IP address. Page 200: Do not, under any circumstances, remove the RCU Link Cable from the primary CPU now running in a single state. Removing the cable might cause the CPU to stop. Page 201: The unit baseplates are easily disconnected from each other by gently prying them apart with a blade screwdriver (see Figure 23 on page 74). Page 202: Do not replace the RCU link cable online in a previous version than 5.0. The support for online replacement also depends on hardware Product Revision levels. Please consult Release Notes (3BSE021377*) for detailed information. Page 428: If you use other power supplies, except SD82X and SD83X, to provide the 24V d.c. for AC 800M it is required that they also are CE marked, Underwriters Laboratories (UL ) listed and fulfill the LVD (SELVandPELV) criteria. Page 428: The AC 800M modules are IP20 semi-protected equipment and must be mounted in non-public localities.
>>
HC-R065D Veterinary Equipment 7 Inch Touch Screen Fluorescence Quantitative Analyzer Canine Progesteron Test Machine
>>
Aluminum Alloy Heavy Duty Sliding Folding Door Hardware Hinge For Casement Door And Window
>>
Semi-Servo Specialized Baby Diaper Production Line with CE (YNK400-HSV))
>>
Module spare parts 5302-MBP-MCM4
>>
HAVEN brand Hydraulic Guillotine Shearing Machine Steel Plate Cutting Machine
>>
Industrial Garment Factory Straight Insert Sewing Center Table
>>
Hydraulic Reversible Furrow Plough Share Plow Moldboard Plough
>>
4m 6m 8m 10m 12m Aerial Work Platform Electric Aluminum Alloy One Man Single Mast Lift
>>
Acrylic Plastic Sheet Press Cutting Machine (HG-B30T)
>>
Good quality electric fat bike 500W 1000W new 2022
>>
New Crop Fava Beans with Top Quality Peeled Split Canned Broad Beans
>>
Charging Cable 5.0 Wireless Earphones HiFi ABS Bass Stereo Noise Waterproof Sport Earbud
>>
Optimum Manufacturing Complete Feed Pellet Mill Production Line
>>
German Type Machinist Hammer with Fiberglass Handle
>>
China Products/Suppliers High Precision CNC Lathe Machine with CE Certification
>>
Far infrared drying oven
>>
15.6 Inch Remote Control Video Picture Frame Auto Play Video Digital Photo Frame Black White Color
>>
HC-B027 Hospital Lab equipment Touch screen 30 Channels ESR Analyzer
>>
CNC Gantry Movable Three-Dimensional Drilling Machine for Big H-Beam Bd3028
>>
Anticorrosion Sacrificial Anodes of Zinc/ Sacrificial Magnesium/ Aluminum Anode/Ships/Yacht/Boat
