Hydraulic Concrete Mixer Truck Excavator Hydraulic Parts Pump

Product Description

Product Description
Hydraulic Concrete Mixer Truck Excavator Hydraulic Parts Pump
Engine Parts Including:

Crankshaft	Cylinder Head	Cylinder Liner	Cylinder Block
Camshaft	Injector	Filter	Fuel Pump
Water Pump	Piston	Turbocharger	Connecting Rod
Gear Ring	Engine Assembly	Flywheel	Injection Valves
Bearing Bushes	Full Gasket Set	Intake Valve	Exhaust Valve

Engine Parts : Piston,liner, gasket set, bearing, valve, crankshaft,connect rod, camshaft,cyl block,cyl head, turbo,starter, water pump, alternator, feed pump, injector, fuel pump.......
Hydraulic Parts: Hyd pump,gear pump,regulator swing motor,travel motor,main control valve, panetary carrier assy,sun gear, panetary gear, cyl block&valve plater, piston shoe,........
Undercarriage Parts: carrier roller,bottom/track roller, idler,sproker, track shoe, track link, adjust cyl,arm/boom/bucket cyl, adjust spring, exvavator bucket, bucket teeth/tip......
Electronic Parts : Throttle/stepper motor,electric appliance,Pressure Switch, Sensor, Switch Start Flameout Solenoid , monitor, controller/ECU......
Cabin Parts : Complete Cabin, Cabin door, door panel, engine cover, Raditator, hyd oil cooler, Condenser, air condenser.......

Detailed Photos
Product Parameters
Applicable Models:

THE MODELS FOR EXCAVATOR/BULLDOZER
FOR-HITACHI
EX40-1	EX40-2	EX55	EX60	EX60-2	EX60-3	EX60-5	EX70	EX75
EX100	EX110	EX120	EX120-1	EX120-2	EX120-3	EX120-5	EX130-1	EX200-1
EX200-2	EX200-3	EX200-5	EX220-3	EX220-5	EX270	EX300	EX300-1	EX300-2
EX300-3	EX300-5	EX300A	EX330	EX370	EX400-1	EX400-2	EX400-3	EX400-5
EX450	ZAX30	ZAX55	ZAX200	ZAX200-2	ZAX330	ZAX450-1	ZAX450-3	ZAX450-5
ZX110	ZX120	ZX200	ZX200-1	ZX200-3	ZX200-5G	ZX200LC-3	ZX210	ZX210-3
ZX210-5	ZX225	ZX240	ZX250	ZX270	ZX300	ZX330	ZX330C	ZX350
ZX450	ZX450LC	ZX500	ZX500LC	ZX520	ZX670	ZX690	ZX870	ZX130
ZX170	ZX170LC	ZX195	ZX260	ZX360	ZX360LC	ZX400	ZX470	ZX490
FOR-KOMATSU(EXCAVATOR)
PC20-7	PC30	PC30-3	PC30-5	PC30-6	PC40-7	PC45	PC45-2	PC55
PC120-6	PC130	PC130-7	PC200	PC200-1	PC200-3	PC200-5	PC200-6	PC200-7
PC200-8	PC210-6	PC220-1	PC220-3	PC220-6	PC220-7	PC220-8	PC270-7	PC202B
PC220LC-6	PC220LC-8	PC240	PC300	PC300-3	PC300-5	PC300-6	PC300-7	PC300-7K
PC300LC-7	PC350-6/7	PC400	PC400-3	PC400-5	PC400-6	PC400LC-7	PC450-6	PC450-7
PC600	PC650	PC750	PC800	PC1100	PC1250	PC2000
FOR-KOMATSU(BULLDOZER)
D20	D31	D50	D60	D61	D61PX	D65A	D65P	D64P-12
D80	D85	D155	D275	D355	D85PX	D85EX	D65EX
FOR-CATERPILLAR(EXCAVATOR)
E200B	E200-5	E320D	E215	E320DL	E324D	E324DL	E329DL	E300L
E320S	E320	E320DL	E240	E120-1	E311	E312B	E320BL	E345
E324	E140	E300B	E330C	E120	E70	E322C	E322B	E325
E325L	E330	E450	CAT225	CAT312B	CAT315	CAT320	CAT320C	CAT320BL
CAT330	CAT322	CAT245	CAT325	CAT320L	CAT973	CAT939C	CAT963C	CAT313
CAT323	CAT318	CAT326	CAT328	CAT329	CAT336	CAT340	CAT345	CAT349
FOR*CAT-ERPILLAR(BULLDOZER)
D3	D3B	D3C	D3D	D4	D4C	D4D	D4E	D4H
D5	D5B	D5C	D5D	D5H	D5M	D6	D6C	D6D
D6H	D6M	D6R	D6G	D6N	D7	D7C	D7D	D7E
D7F	D7G	D7H	D7R	D8	D8R	D8N	D8H	D8T
D8L	D8K	D8G	D8M	D9	D9L	D9N	D9R	D9T
D10	D10R	D10N	D10T	D11	D11R	D11N
FOR-KOBELCO
SK120-6	SK120-5	SK210-8	SK210LC-8	SK220	SK220-1	SK220-3	SK220-5/6	SK200
SK200	SK200	SK200-3	SK200-6	SK200-8	SK200-5/6	SK60	SK290	SK100
SK230	SK250	SK250-8	SK260LC-8	SK300	SK300-2	SK300-4	SK310	SK320
SK330-8	SK330	SK350LC-8	SK235SR	SK450	SK480	SK30-6
FOR-SUMITOMO
SH120	SH120-3	SH200	SH210-5	SH200	SH220-3	SH220-5/7	SH290-3	SH350-5/7
SH220	SH280	SH290-7	SH260	SH300	SH300-3	SH300-5	SH350	SH60
FOR-VOLVO
EC160C	EC160D	EC180B	EC180C	EC180D	EC210	EC210	EC210B	EC240B
EC290	EC290B	EC240	EC55	EC360	EC360B	EC380D	EC460	EC460B
EC460C	EC700	EC140	EC140B	EC160B	EC350	EC350DL	EC480	EC340
FOR-LIEBHERR
R914	R924	R934	R944	R916	R926	R936	R954	R966
R974	R984
FOR-KUBOTA
JH60-7	JH115	JH135	JH161	JH185
FOR-DAEWOO
DH200	DH220-3	DH220	DH220S	DH280-2	DH280-3	DH55	DH258	DH130
DH370	DH80	DH500	DH450	DH225	DH150	DH330	DH400	DH580
FOR-HYUNDAI
R60-5	R60-7	R80-7	R200	R200-3	R210	R210-1	R210-9	R210LC
R210LC-7	R225	R225-3	R225-7	R250	R250-7	R290	R290LC	R290LC-7
R320	R360	R954	R205	R210-5	R215	R230	R235	R275
R300	R385	R485
FOR-KATO
HD512	HD1430	HD512III	HD820III	HD820R	HD1430III	HD700VI	HD1250VII	HD250SE
HD400SE	HD500SE	HD1880
FOR-DOOSAN
DX225	DX225LC	DX258	DX300	DX300LCA	DX420	DX430	DX140	DX150
DX220	DX250	DX255	DX260	DX370	DX480	DX520
FOR-SHANTUI
SD13-2	DH16J2XL	DH16J2LGP	SD16	SD22	SD32
FOR-CASE
CX210	CX210B	CX210C	CX210D	CX210LC	CX225	CX235	CX235C	CX240
CX240C	CX245	CX250	CX250C	CX300	CX300C	CX330	CX330C	CX350
CX350C	CX460	CX460LC	CX470	CX470C	CX490	CX490D	CX700	CX700B
CX750	CX750D
FOR-JCB
JS200	JS200SC	JS210	JS210SC	JS220	JS220LC	JS230	JS230LC	JS240
JS240LC	JS290	JS290LC	JS300	JS300LC	JS330	JS330LC
FOR-XCMG
XE55DA	XE60DA	XE65DA	XE75DA	XE80C	XE80D	XE85C	XE85D	XE135D
XE155DK	XE150D	XE155D	XE200DA	XE200D	XE200C	XE205DA	XE215DA	XE215C
XE215D	XE215HB	XE225DK	XE230C	XE245DK	XE240D	XE260C	XE265C	XE270DK
XE305D	XE335DK	XE335C	XE370D	XE370DK	XE370CA	XE370C	XE380DK	XE470D
XE490DK	XE490CK	XE500HB	XE520DK	XE550DK	XE750D	XE750G	XE950D	XE950G
XE950DA	XE55	XE60	XE65	XE75	XE80	XE85	XE135	XE150
XE155	XE200	XE205	XE215	XE225	XD230	XE240	XE245	XE260
XE265	XE270	XE305	XE335	XE370	XE380	XE470	XE490	XE500
XE520	XE550	XE750	XE950
FOR-MITSUBISHI
MS30	MS110	MS110-3	MS110-5	MS110-8	MS180
FOR-SAMSUNG
SE210	SE280	SE320
FOR-IHI
IHI35	IHI50	IHI55	IHI60	IHI75
FOR-YMMA
YM15	YM30	YM35	YM55	YM65	YM85
FOR-LIUGONG
LG906C	LG907	LG200	LG220	LG925	LG934

Undercarriage Parts: Front Idler Assy, Carrier Roller Assy SF, Track Roller Assy, Track Shoe Assy, Track Roller Assy DF, Track Link, Segment, Track Shoe, Specket, Track Group
Packaging & Shipping
Company Profile
Exported Experience:
Since 2005, we have been engaged in the export business of engineering machinery engines and Parts/accessories, Undercarriage Parts, Mini/Small excavators, backhoe loader, Skid Steer Loard and Attachments. Mainly exported to countries and regions such as Europe, the United States, Canada, Mexico, Brazil, and Southeast Asia with ISO, CE certificates.
Various Parts in Stock
1. Engine, hydraulic pump, distribution valve, center rotation, slewing bearing, walking drive, cab, control valve, relief valve, main control multi way valve, etc
2. Hydraulic Parts: main oil seal | repair kit | O-ring | water pump repair kit | hammer repair kit | distribution valve repair kit | hydraulic pump repair kit | rotary pump repair kit | oil cylinder repair kit | walking motor repair kit | hydraulic cylinder | piston | middle arm cylinder | bucket cylinder | cylinder barrel | tension cylinder | piston rod | large screw nut | boom cylinder
3. Electrical Parts, Including: starter motor computer board | automatic refueling motor | lever assembly | display screen | throttle cable | solenoid valve | Xiao | horn button | relay | instrument panel | fuse | monitor | control panel | air conditioning compressor | vehicle wiring harness | oil suction pump | governor | connector | timer | plug | pre thermal resistor | fuse | fuse | diesel meter | horn assembly | controller | on Off | Magnetic switch | Hydraulic pump pressure switch | Oil pressure switch | Stop switch | Ignition switch | Sensor | Water temperature sensor | Oil sensor | Diesel sensor | Automatic throttle motor sensor | Sensor | Single foot sensor | Angle sensor | Speed sensor | Pressure sensor
4. Undercarriage Parts: including; Idler | Carrier roller | Support roller | Drive teeth | Chain | Chain connection | Chain pin | Bucket shaft | Four wheel belt | Chain rail assembly | Idler bracket | Rotary support | Track | Rubber track | Track assembly | Track plate | Tensioning device | Tensioning cylinder seat | Tensioning cylinder | Universal cross shaft | Chain plate screw | Big spring | Chain plate | Chain link | Chain guard frame | Bottom guard plate
5. Bucket, rock bucket, reinforced bucket, ditch bucket, grid bucket, screen bucket, cleaning bucket, tilting bucket, thumb bucket, trapezoidal bucket
6. Excavator quick change joint, excavator oil cylinder, crushing hammer, hydraulic shear, hydraulic compactor, vibrating hammer, bucket teeth, tooth seat, track, carrier roller, support roller
And Other related machineries parts:
Excavator, wheeled excavator, loader, small loader, forklift, sliding loader, excavator loader , bulldozer, scraper, dump truck, mining truck, roller, single steel wheel roller, double steel wheel roller, tire roller, small roller, compactor, smooth wheel roller, three wheel roller, sheep foot pressure Road machine, impact compactor, flat compactor, vibration compactor, dynamic compactor, hand-held compactor etc.
Our Advantages
1. The company has a stable and friendly supply and demand relationship with more than 20 factories for a long time, with reliable quality, stable supply of goods, and timely and professional after-sales service.2. The company has professional customer service personnel, sales team, and after-sales service team, which can provide online video after-sales service. If conditions permit, on-site service is also available.


FAQ
Q1: Are you trading company or manufacturer ?
A: We are an industry and trade integrated enterprise.
Q2. How is your after-sales service?
1. We implement factory joint warranty services: our after-sales service personnel assist customers and cooperate with our factory's technical personnel to implement two service modes: online and offline;
2. Each product has a certain warranty period, and within the warranty period, free accessories are provided; Unexpected warranty period, only the cost of accessories will be charged. All shipping costs are borne by customers;
3. If conditions permit, we can appoint technicians to provide on-site services.
Q3. What are your terms of delivery?
A: EXW, FOB, CFR, CIF.
Q4: What quality level does your product belong to?
A: We have been engaged in the export business of these products since 2005 and have established a sound quality control system. According to the procurement needs of different markets and customers, we mainly focus on products with high, medium quality, with original parts as the main component and aftermarket parts as the auxiliary.
Q5. How about your delivery time?
Generally, within 5-10days after your payment.
If we do not ship the goods after receiving payment, you can directly file a complaint with the Chinese embassy or consulate in the local area, and the cost will be borne by our company.
Q6: How do you make our business long-term and good relationship?
A:1. We keep good quality and competitive price to ensure our customers benefit ;
2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.
Thank you very much for your attention. Kindly Please feel free to contact us at any time. Welcome to back to your HOME

---

>> Custom logo printed kraft paper bag handbag custom handle boxes packaging gift paper shopping bag
>> Enjoy Hot Sale 570W Solar Panel with 31PCS/Pallet Package Details
>> Popular Vertical Automatic PVC Labels Micro Injection Machine
>> 3# Fabric Tape Invisible Zipper
>> Dyjx Horizontal Type Ribbon Mixer Double Screw Ribbon Blender Mixing Machine for Mushroom Raw Material Ice Cream Dry Powder
>> Tder Chinese Hydraulic Control Valve Wheel Excavator Price
>> Sunshing Clear Plastic Flash Drive Storage Case USB-Stick Holder with White Foam
>> 216mm SBNC BK-L216II Thermal KIOSK Printer A4 Auto Cutter ATM/Vending Machine Embedded Printer
>> Low Consumption Factory Directly Supply Industrial High Efficiency Deodorization Machine
>> Heavy Duty Large HDPE Industrial Logistic transport Warehouse Storage Foldable Collapsed Pallet Box sealing welding machine
>> Rectangular Tinplate Tin Free Steel Can Lid Easy Open End TFS Eoe for Tuna Fish Meat
>> Shine and Jam Gel Automatic Honey Tomato Cheese Mayonnaise Paste Piston Pump 4 Heads Filling Machine Metal Cap Torquing Elevotor Single Side Top Side Label Appl
>> Best Selling SL Track Full Body 3D 0 Gravity Massage Chair
>> Plastic Pulverizer PE Miller PP Milling Machine
>> Popular Model Deburring Machine
>> FULL GASKET FOR KIA HYUNDAI IX35
>> Top Quality (Puffy) Sbs for Hot Melt&Adhesives
>> SUS316 Humidity Sensor Housing For Sensor Probe
>> Cheap price China mini excavator small excavator crawler excavator 1 ton 2 tons for sale
>> Alloy CNC Wheel Renovation Diamond Cutting Machine on Sale