Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN4580-TV | 45 | 80 | 60 | 42.5 | – | – | 25 |
| 70 | – | – | 11.5 | – | – | 0.3 | 0.6 |
|
| 71 | 60 | 61,000 | 177,000 | 38,000 | 74,000 | 4,000 | 1,500 | 1.2 | 3,000 | 1,340 | 5.33 | 1 | 1.12 |
| ZARN4580-L-TV | 45 | 80 | – | – | 75 | 57.5 | 25 |
| 70 | 56 | 68 | 11.5 | 26.5 | 12 | 0.3 | 0.6 |
|
| 71 | 54 | 61,000 | 177,000 | 38,000 | 74,000 | 4,000 | 1,500 | 1.2 | 3,000 | 1,340 | 6.03 | 1 | 1.27 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Aluminium louvered roof system motorised aluminium louver pergola outdoor
>>
Fasteners Customized Fastener Metal Stamping Parts HSS Die Punching Mould
>>
Taijia TEM-H410 Concrete Slab Company Floor Concrete Slab Detector
>>
2022 Hot Sale Cheaper Factory Price Color LED Light Effect Wired 8d Optical Computer Gaming Mouse for Professional Gamers
>>
Cutomzied Big Beer Label Printed Vinyl Film Tablecloth for Beer Advertising Pub Decoration
>>
2021 Affordable Second-Hand 20 Ton Crawler Excavator for Sale
>>
Wholesale Low MOQ Cotton Crew Unisex Men Women Children Custom Logo Sports Socks
>>
Aluminum Alloy Sound Insulation and Heat Insulation Villa Balcony Room Door and Window Hollow Glass Sliding Window
>>
High Precision Blin Swiss Type CNC Lathe Machine with ISO 9001
>>
Cheap Price LED Mini Projectors HD LCD Portable Projector /Proyector/Beamer
>>
Self Moving Agricultural Rotary Tiller, Ditching, Weeding, and Loosening Machine
>>
Amber Plastic PSU Polysulfone Rod
>>
2056900100 L 2056900200 R FRONT FENDER INNER PLATE CAR PARTS W205 FOR MERCEDES BENZ
>>
Stainless Steel Jacket Half-Pipe Chemical Chemical Equipment Forepoxy Resin Glue Reactor
>>
15kHz 2600W Ultrasonic Generator System Digital Ultrasonic Good Quality Sonotrode Booster Horn
>>
Battery Manufacturer Low Self-Discharge Rechargeable 1.2V NiMH Rechargeable Battery Pack AAA 2700mAh Ni-MH AA D C 9V Rechargeable Batteries for Wireless Mouse
>>
Truck Transportation Service Road Freight Trucking Logistics Sensitive Cargo Shipping Agent to The World
>>
HIGH QUALITY GLB CLASS W247 CENTER BASIC BRACKET FOR FRONT BUMPER 2478856500
>>
New original laptop battery for macbook battery 13'inch A1331 A1342 Late 2009/Mid 2010
>>
12 Channel Reagent Reservoir 22ml Multi Well for High Profile Design
