Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN3585-TV | 35 | 85 | 66 | 43 | – | – | 20 |
| 73 | – | – | 14 | – | – | 0.3 | 0.6 |
|
| 74 | 60 | 105,000 | 265,000 | 27,500 | 53,000 | 4,000 | 1,250 | 2.3 | 3,500 | 1,300 | 8.47 | 1 | 1.65 |
| ZARN3585-L-TV | 35 | 85 | – | – | 82 | 59 | 20 |
| 73 | 60 | 73 | 14 | 30 | 12 | 0.3 | 0.6 |
|
| 74 | 58 | 105,000 | 265,000 | 27,500 | 53,000 | 4,000 | 1,250 | 2.3 | 3,500 | 1,300 | 10.4 | 1 | 1.8 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Factory Direct Sales T/C 9010 13372 63''
>>
Wall Mounted Horse Saddle Rack, Heavy Duty Western and English Saddle Storage, 3 Tier Equestrian Saddle Stand Holder for Horses Supplies Accessories
>>
Micro Tagging Gun for Thin fabrics, delicate underclothes
>>
rebar detection ferro scanning system concrete reinforcement rebar scanner
>>
OEM ODM Ride on Trojan Electrical Plush Toy Custom Kids Wooden Rocking Horse Toy
>>
YFMA-920 High Speed Film Paper Automatic Laminating Machine
>>
8HP 10HP 12HP E-Start Hand Tractor with Rotary Tiller for Farm Use
>>
Vertical 1200kg 1500kg/Batch High Speed TPR TPE Granules Pellets Powder Mixer
>>
SAK-TC212S-8F133N AC
>>
Gfrp Pipe Fittings, Elbow, Tee, Reducer, Flange Winding Machine for Diameter DN100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600mm
>>
Manufacturer Customized Stainless Steel Woven Mesh Cylinder Filter Tube
>>
Solar Flashing Safety Light Outdoor LED Traffic Signal Light
>>
HS15N Auto AC Compressor Lada Priora 1.6 2007-2018 F500SC8AA01 21700811101210
>>
100% virgin quality PE/ ABS double color plastic sheet/ board
>>
diamond Style For BMW 3 SERIES F30 car grille silver general front grilles
>>
Emergency Hand Crank Self Powered with LED Flashlight 1000mAh Power Bank
>>
Precision Sheet Metal Stamping for Machined Part
>>
4 Axis Inner and Outer Hole CNC Grinding Machine for Gear
>>
Basketball Court Marking Stencil Kit
>>
Products 2022
