Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN4075-TV | 40 | 75 | 54 | 37 | – | – | 20 |
| 65 | – | – | 11 | – | – | 0.3 | 0.6 |
|
| 66 | 55 | 59,000 | 163,000 | 27,500 | 53,000 | 4,400 | 1,600 | 1 | 2,800 | 1,030 | 3.78 | 1 | 0.9 |
| ZARN4075-L-TV | 40 | 75 | – | – | 70 | 53 | 20 |
| 65 | 50 | 63 | 11 | 27 | 12 | 0.3 | 0.6 |
|
| 66 | 48 | 59,000 | 163,000 | 27,500 | 53,000 | 4,400 | 1,600 | 1 | 2,800 | 1,030 | 4.35 | 1 | 1 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
10% off Modern Aluminum Entry Interior Exterior Main Front Wrought Iron Single Double Gate Garage Security Metal Iron Glass New Entrance Steel Pivot Door
>>
20kHz Ultrasonic Sewing Machine for PVC Non-Woven Fabric Various Materials
>>
China High Quality Automatic Saving Energy 19 Liter 20L 5 Gallon Water Bottle Disposable Non Spilled Cap Injection Molding Machine
>>
High Quality and Super Effective Summer Hot Selling Black Mosquito Coil
>>
Factory Supply High Quality Flattened expanded metal mesh for outdoor BBQ
>>
C35 Candle E14 2W LED Filament Bulb (pH6-3005)
>>
6-12mm Precision Three Point Inside Micrometer
>>
Heat Setting High Speed Customized Mg Pick up Felt for Paper Mills
>>
Easy Operating Zk20 Drilling Machine with Slide Table
>>
Customized Biodegradable Disposable Eco-Friendly Bamboo Sushi Chopsticks with Full Paper Package
>>
Zesty Lemon Infused Vitamin Tea for Energy and Hydration
>>
Mechanical Stainless Console with Steering System (2900-S)
>>
Standing desk
>>
European Style 3-Point Mounted Rotary Tiller for Tractors
>>
Factory Price Ceramic Basin Variety of Styles for Your Choice Bathroom Sink Color Pink Wash Basin
>>
Ce Certificate Automatic Plastic Crusher Knife Blade Grinding Sharpening Machine Sharpener
>>
37m 52m 56m 62m Concrete Pump Truck Hb37 Hb52 Hb58 Hb62
>>
hang tag seal in garment
>>
Taijia Integrated Floor Thickness Gauge Non-ferromagnetic Dielectric Thickness Tester,Non-destructive Concrete Structures Tester
>>
Rimless Wall Hanging Wc Toilet with Concealed Cistern Tank
