HIMA F7126

Product Details

Product Description

Product Description
Brand: HIMA
Type:F7126
Origin: the United States
Warranty: 365 days
Colour: new/used
Shipping method: Courier delivery
Module of PLC, DCS, ESD system card, the card is a vibration monitoring system, steam turbine control system module, the advantages of the gas generator spare parts brand: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts of our products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, mechanical, electronic manufacturing, automobile manufacturing, plastic machinery, electric power, water conservancy, water treatment/environmental protection, boiler heating, energy, power transmission and distribution and so on.
505E Controlling Parameters The controlling parameter status of the 505E uses two Analog Read registers (3:0070) & (3:0071) to identify the two parameters that are in control of the 505E. The analog register (3:0070) corresponds to the top line of the display. Analog register (3:0071) corresponds to the second line of the display. These variables follow what is displayed on the controlling parameter screen, under the ‘CONT’ key. The variables gives the current status of the control and is defined in the following table.
Specific Address Information Entering Setpoint from the Modbus The setpoints for the Speed, Extraction, Cascade and Auxiliary can be entered through the Modbus link. When the setpoint is entered for any of these functions the setpoint will not move instantly, but the setpoint will move towards the entered setpoint at the ‘entered rate’ defined for the function in the program mode (see Direct Setpoint Entry information in Chapters 3 and 5). The direct setpoint entry from Modbus functions the same as entering the setpoint from the front panel of the control. Manual 85018V1 505E Digital Governor Woodward 199 There is feedback provided to let the operator know what value was entered. This value will not change until a new value is entered from the Modbus. The addresses, 3:0060- :0063, are for speed, cascade, auxiliary, and extraction/admission respectively. When the a new value is entered from the Modbus, the setpoint will move to the new value. If the entered setpoint that is the same as the feedback, the operator can use a ‘Go To Modbus Entered’ setpoint command (0:0017, 0:0029, 0:0037, & 0:0063) instead of entering the setpoint again. This command needs to be used when the setpoint to be entered is the same as the feedback. Modbus Scale Factors Modbus has two limitations: • only integers can be sent across; • the value is limited between -32768 and 32767. These limitations can be overcome by scaling the value before it is sent across the Modbus. The default scale factor for the analog values is 1. The scale factor can be changed in the Service Mode between 1 and 100. The following input and setpoint values that are sent across the Modbus have independent scale factors: Casc (3:0030), Aux (3:0037), FSP (3:0041), KW (3:0045), Sync/Load Share (3:0043), and Extr/Adm (3:0056). These scaled parameters and their scale factor are available through the Modbus. Values that require a decimal point must be multiplied by the scale factor (10, 100) prior to being sent across the Modbus. The value sent must then be divided by the scale factor in the Master. The Scale Factor adjusts all associated analog reads and writes accordingly. For example, the Cascade Scale Factor adjusts the cascade input and setpoint analog read values as well as the Entered Setpt analog write value. For example, if the Cascade setpoint of 60.15 needs to be sent across the Modbus and have two decimal places, the Cascade Scale Factor would be set to 100 in the Service Mode. This will change the value so that the decimal places can be sent across the Modbus communications link (60.15 * 100 = 6015). After the value is sent across the Modbus, it must be rescaled in the Master to the original value (6015 / 100 = 60.15). A Directly Entered Cascade Setpoint (4:0002) of 61.5 would be sent across the link as 6150 and the 505E automatically divides the value by the Casc Scale Factor and uses the value of 61.5 as the setpoint desired.

---

>> 125ton 4000mm Da41s Hydraulic Plate Press Brake
>> Automatic Small Type Baseball Cap Making Machine Single Head Hat Cap Mould Ironing Machine
>> Fully Automatic 1500ml Mineral Water Bottle Making Machine Price for Pet Bottle Blower
>> 15L Commercial Triple Tank Slush Machine for Refreshing Beverages
>> Headband Wigs for Black Women Human Hair Glueless None Lace Front Wigs
>> Saudi Arabia Army Style Embossed Leather High Cut Military Style Boots
>> OEM customized GSM, WIFI, 3G, 4G LTE, 5G, indoor outdoor high gain car antenna
>> Hot sale high quality and with competitive wheelchair
>> gym body leg arm chest waist belly thigh hip bottom behind buttocks abs plastic fat body measuring tape
>> 340mm clutch disc plate 70-1601130 for MTZ tractor
>> 2.5cbm Industrial Sunway Plywood on Grid Complete Solar Power System with Cheap Price Sw-5kw-on
>> Sibolux Fan-Factory 18-Inch Electric-Fan for Home Cheap-Price Low Pedestal Standing-Fan 5-Blades
>> Sy75c Crawler Excavator Used 7.5 Tons Mini Diggers for Sale Cheap Price
>> aluminium handmade frames
>> Hot New Motorcycle Parts Digital Tachometer Rpm Motorcycle Refitting Tachometer Rpm Led Electronic
>> Cocoa Liquor Pressing Machine Hydraulic Oil Press Machine Cold Oil Presser
>> OEM Video Greeting Card for Promotion
>> Custom sugar packet lollipops stand up pouch packaging with zipper mylar bags
>> BIOHAZARD BAG, AUTOCLAVE SACK, SAMPLING BAG, SHARP CONTAINER, MEDICAL BIN, SAFETY BOX, BOTTLE
>> Byloo mobile height board height measuring stadiometer wall stadiometer calibrated mobile stadiometer height board