Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN2557-TV | 25 | 57 | 50 | 35 | – | – | 20 |
| 47 | – | – | 10 | – | – | 0.3 | 0.6 |
|
| 48 | 39 | 35,500 | 86,000 | 22,600 | 36,000 | 6,000 | 1,900 | 0.55 | 1,900 | 350 | 0.989 | 1 | 0.53 |
| ZARN2557-L-TV | 25 | 57 | – | – | 65 | 50 | 20 |
| 47 | 36 | 45 | 10 | 25 | 11 | 0.3 | 0.6 |
|
| 48 | 34 | 35,500 | 86,000 | 22,600 | 36,000 | 6,000 | 1,900 | 0.55 | 1,900 | 350 | 1.15 | 1 | 0.59 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
CNC Wire Cut EDM (DK7763F)
>>
Adhesive waterproof large size medical foam hydrocolloid wound dressing
>>
Cheap raw almond in shell nuts Organic badam almond nuts Wholesale bulk badam nut
>>
China Supplier Hot Selling Cold Extrusion Sleeve For Building
>>
AC85-265V Warm White 3000K 3500K 5700K E26 E27 25W CRI98 Full Spectrum PAR30 LED Globe Bulb
>>
2022 cheap biodegradable food tray disposable bamboo wooden plate sushi wooden plate
>>
Snowmobiles 200cc Go Kart Snow Mobile for Kids 125cc Gasoline Snow Scooter
>>
Hot Sales New Fashion Students Gifts Cute Stationery Folding Pencil Pouch Bag Rainbow Color Girls Pencil Cases
>>
Premium UHP 500 High Density Graphite Electrodes for Steel Production
>>
padel rackets accessories Pickleball Paddle flat grip colorful overgrip padel racket
>>
Micro DC reduction motor GM12-N20 metal gear reduction motor automatic lock low speed
>>
Rigid chain, pin tooth chain, horizontal push zipper, lifting chain, bite chain, transmission chain, elevator
>>
Automatic liquid bagging packing packaging filling sealing machines for water bottle
>>
Shandong Yantai Popular Fresh Fruit Crisp Juicy High Quality FUJI Apple
>>
108 L Filter Equipment Aircraft Parts Cylinder Diesel Mould Injector Customize Industrial Ultrasonic Cleaner
>>
Cattle Adjustable Headlock Dairy Farm Headlock Galvanized Headlock Self Lock Cow Headlockneck
>>
Farm Land Scraper Machine Laser Control 2m Width Leveler Land Leveling Laser
>>
2018 Low-e and soundproof aluminum roof skylight
>>
Customized Injection Mould for Barrel Damper Valve D0200701 OEM Auto
>>
Wholesale Soft Silicone Training Toothbrush Silicone Koala Teether Baby Care Teething Brush
