Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN3570-TV | 35 | 70 | 54 | 37 | – | – | 20 |
| 60 | – | – | 11 | – | – | 0.3 | 0.6 |
|
| 61 | 50 | 56,000 | 148,000 | 26,000 | 47,000 | 4,800 | 1,700 | 0.9 | 2,600 | 740 | 2.8 | 1 | 0.8 |
| ZARN3570-L-TV | 35 | 70 | – | – | 70 | 53 | 20 |
| 60 | 45 | 58 | 11 | 27 | 12 | 0.3 | 0.6 |
|
| 61 | 43 | 56,000 | 148,000 | 26,000 | 47,000 | 4,800 | 1,700 | 0.9 | 2,600 | 740 | 3.21 | 1 | 0.93 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Satisfactory Welding Tube Mill, User-Friendly and Versatile, Perfect for All Your Needs
>>
Factory Price Wine Egg Oil Bag in Box Filler / Bib Filling Machine / Bag in Box Filling Machine
>>
concrete hammer tester
>>
Factory Wholesale 6mm Tungsten Carbide Rod and Round Bar with H6 Tolerance
>>
2024 Brand New Automatic Animal Sheep Cattle Horse Goat Feed Equipment Camel Cow Goat Feed Machine with CE
>>
Horizontal Plough Mixer for Seasoning Spices
>>
1 Year Hydraulic Pressure Hydraform Brick Block Making Machine QS1300
>>
2000*4000mm End Face Milling Machine for Cross Sectional of H Beam and Box Beam
>>
Hot Selling Dart Games Toys Product Can Be Hung Customized Color
>>
Automatic Flow Pack Ice Cream Bar / Ice Popsicle / Chocolate Bar Flow Type Pillow Bag Packaging Machine
>>
FUJI Car Lift Freight Elevator Goods Elevator Car Elevator with Good Price From China Factory Manufacturer Vvvf Control
>>
Waste Plastic Manhole Cover Production Line with Hydraulic Press for Municipal Projects
>>
216EA61B ABB module supply
>>
Ce Approved Automatic Piston Liquid Olive Oil Filling Machine
>>
High Quality Sliding Window with Double Glazing
>>
Round GPS Rotate Camera Amoled 4G SIM Card Health Monitor Video Call Bracelet Sport Wrist Large Battery 760mAh Smart Watch for Men Women
>>
Disposable Hair Net Food industrial bouffant cap Elastic Nonwoven Disposable Clip Cap Mob Cap
>>
Automatic Single Nozzle High Accuracy Down Feather Filling Machine
>>
Aekwondo Shin Protector Forearm Elbow Arm Guards, Wt MMA Martial Arts Kickboxing Karate Sparring Muay Thi Training Match Gym School Academy for Men Women Kids
>>
Rubber Crawler Tractors Large Farm Machine Agricultural Tractor
