Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN5090-TV | 50 | 90 | 60 | 42.5 | – | – | 25 |
| 78 | – | – | 11.5 | – | – | 0.3 | 0.6 |
|
| 79 | 67 | 90,000 | 300,000 | 40,000 | 82,000 | 3,600 | 1,200 | 2.2 | 4,800 | 2,470 | 8.42 | 1 | 1.43 |
| ZARN5090-L-TV | 50 | 90 | – | – | 78 | 60.5 | 25 |
| 78 | 60 | 78 | 11.5 | 29.5 | 12 | 0.3 | 0.6 |
|
| 79 | 58 | 90,000 | 300,000 | 40,000 | 82,000 | 3,600 | 1,200 | 2.2 | 4,800 | 2,470 | 10.46 | 1 | 1.78 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
61CM Ice Fishing Rod , Glass fiber ice fishing rod
>>
10000t Hydraulic Forging Press for Wheel Hub
>>
China Factory Latex Organic Fiber Palm Fibre Mattress Spring Sponge Foam Mattress Pillow Cushion Hotel Floor Latex Windmill Palm Coconut Coir Mattress
>>
Complete 1-10tph Animal Feed Pellet Production Line Cattle Feed Plant Chicken Feed Making Machine Pig Cow Goat Sheep Feed Pellet Mill Machine
>>
Free Shipping Chinese 60V 1 Ton 1.5 Ton 2 Ton 5 Ton Mini Electric Forklifts Trucks Price Battery Forklift Electric for Sale
>>
50 ton per day small maize flour miller turnkey corn milling company business plan automatic maize mill machine for sale
>>
Morden Design Hot Sale Round Aluminum Dining Table Solid Wood Cafe Table for Hotel Restaurant Kitchen Use
>>
2800kN PP PVC PE ABS Desktop Injection Molding Machine
>>
Casual EVA Platform Clogs Fashion Clogs
>>
Polyester Necktie, Custom Pattern Necktie, Woven Necktie, Yarn-Dyed Jacquard Necktie
>>
Vibration Machine OEM Pivot Wooden Box Packaging Granite Polisher Floor Polishing
>>
Sublimated Ice Hockey Wear Made To Order From 2022 Best Supplier.
>>
55GSM Medical Approved Elastic Thick PBT Bandage 10cm X 4m
>>
Wholesale Low MOQ Hot Selling Reusable Purple Lady Crystal Hair Remover Razor Set
>>
Powered Sugar Emulsifying Pump with Reliable Sealing
>>
High Quality 300 People Wedding Marquee Party Tent for Sale
>>
Women Lady Girl Body Cleaning Pink Private Label Eco-Friendly Changeable Long Double Edge Safety Razor Best Gift
>>
Hot Sale C Steel Purlin Roll Forming Machine Steel Roll Former for Solar Tracker
>>
Good Condition Fish Feed Machine for Floating Fish Feed Production
>>
100% Virgin Material Accept Custom Order FIBC Bag for Packing
