Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN90180-TV | 90 | 180 | 110 | 72.5 | – | – | 35 |
| 160 | – | – | 22.5 | – | – | 0.3 | 1 |
|
| 161 | 130 | 325,000 | 1,030,000 | 98,000 | 210,000 | 1,800 | 700 | 10.5 | 7,700 | 14,500 | 312 | 2 | 11.8 |
| ZARN90180-L-TV | 90 | 180 | – | – | 135 | 97.5 | 35 |
| 160 | 130 | 158 | 22.5 | 47.5 | 16 | 0.3 | 1 |
|
| 161 | 125 | 325,000 | 1,030,000 | 98,000 | 210,000 | 1,800 | 700 | 10.5 | 7,700 | 14,500 | 372 | 2 | 13.2 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Food Additive Sweetener E952 Sodium Cyclamate NF13 Price CAS 139-05-9
>>
Automatic Flow Wrapping Chocolate Bread Cake Donut Crossaint Horizontal Packing Packaging Machine for 80mm height bread
>>
Brilliant-Dragon Carbattery Magnetic LED Strobe Caution Emergency Warning Light
>>
Telescopic rod and reel combo spinning fire fishing rod set fishing reel and rod
>>
Ruibo Automatic Soldering Robot Machine for PCB Assembly
>>
Sn221-414 for 0.08-4mm Wire 4pin 380 Power Good Quality Lighting Cable Connector
>>
Y81-160 China High Quality Hydraulic Steel Cutting Smallest Automatic Alligator Shear Copper Alligator Shear Tiger-Head Shear
>>
Series Digital Izod Impact Tester
>>
Graphite cube
>>
C-3070 Timing Chain Kit for Buick LeSabre 3.8L OEM 25530114 24500030 TK1262
>>
WOODHEAD 5136-PFB-VME in stock
>>
UV Quartz Spiral bulb Light UVC Germicidal Lamp Air Water Disinfection
>>
What procedure does electronic scale export European Union to apply for CE certification need to prepare?
>>
Cheap Used Japan Komatsu PC200 PC220 PC240 Excavator Used Komatsu 24 Ton Excavator Price PC240-8
>>
ASTM D2276 Jet Fuel Particulate Contaminant in Aviation Fuel Tester
>>
Rear Step Bumper for Nissan Navara 2021 2022
>>
0.5L 1L HDPE Plastic Blow Molding Machine/Bottle Making Machine Price
>>
Plastic Crushing and Washing Pet Recycling Line Hot Wash Plastic Bottle Crusher with Washer and Dryer
>>
Seasoning Spice Marinated Garlic in Oil with Chili
>>
australian aluminium windows with australia handle operated awning window
