Product Details
Product Description
Product Description
Brand:TRICONEX
Type:3351
Origin: the United States
Warranty: 365 days
Colour: new/used
Shipping method: Courier delivery
Module of PLC, DCS, ESD system card, the card is a vibration monitoring system, steam turbine control system module, the advantages of the gas generator spare parts brand: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts
Our main products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, mechanical, electronic manufacturing, automobile manufacturing, plastic machinery, electric power, water conservancy, water treatment/environmental protection, boiler heating, energy, power transmission and distribution and so on.
MPU GEAR RATIO dflt= 1.0 (0.05, 100) Enter the speed sensor gear ratio followed by the ENTER key. This value is the ratio of the speed sensor gear to the turbine shaft. This gear ratio is the result of dividing the speed of the speed sensor gear by the speed of the turbine shaft. FAILED SPEED LEVEL (RPM) dflt= 250 (0.5, 1000) Enter the Failed Speed Level (in rpm) followed by the ENTER key to set the speed probe input failure level. If speed drops below this level, the control will determine the speed input device is failed and issue an alarm. If all speed inputs fail, the 505E will issue a trip on loss of speed inputs. (Must be greater than or equal to 0.0204 x Overspeed Test Limit setting) USE SPEED INPUT #2? dflt= NO (Yes/No) Select YES followed by ENTER if both speed inputs are to be used. FAILED SPEED LEVEL (RPM) dflt= 250 (0.5, 1000) Enter the failed speed level (in rpm) followed by the ENTER key to set the speed probe input failure level. If speed drops below this level, the control will determine the speed input device is failed and issue an alarm. If all speed inputs fail, the 505E will issue a trip on loss of speed inputs. (Must be greater than or equal to 0.0204 x Overspeed Test Limit setting) OFF-LINE PROPORTIONAL GAIN dflt= 5.0 (0.0, 100) Enter the off-line PID proportional gain, in repeats-per-second (rps) followed by ENTER. This value is used to set speed/load control response when the Generator or Utility Tie breaker contacts are open (if the unit is a generator) or if the turbine speed is below minimum governor speed (if the unit is not a generator) or when the Select Dynamics function is used and the contact is open. This value can be changed in the Run Mode while the turbine is operating. A recommended starting value is 5 rps. OFF-LINE INTEGRAL GAIN dflt= 0.5 (0.01, 50) Enter the off-line PID integral gain percentage followed by ENTER. This value is used to set speed/load control response when the Generator or Utility Tie breaker contacts are open (if the unit is a generator) or if the turbine speed is below minimum governor speed (if the unit is not a generator) or when the Select Dynamics function is used and the contact is open. This value can be changed in the Run Mode while the turbine is operating. A recommended starting value is 0.5%. OFF-LINE DERIVATIVE RATIO dflt= 5.0 (0.01, 100) Enter the off-line PID derivative ratio followed by ENTER. This value is used to set speed/load control response when the Generator or Utility Tie breaker contacts are open (if the unit is a generator) or if the turbine speed is below minimum governor speed (if the unit is not a generator) or when the Select Dynamics function is used and the contact is open. This value can be changed in the Service Mode while the turbine is operating. A recommended starting value is 5% (see Chapter 5—PID Dynamics Settings for more information).
ON-LINE PROPORTIONAL GAIN dflt= 5.0 (0.0, 100) Enter the on-line PID proportional gain percentage followed by ENTER. This value is used to set speed/load control response when the Generator and Utility Tie breaker contacts are closed (if the unit is a generator) or if the turbine speed is above minimum governor speed (if the unit is not a generator) or when the Select Dynamics function is used and the contact is closed. This value can be changed in the Run Mode while the turbine is operating. A recommended starting value is 5%.
>>
1.75 ton Mini excavator/Crawler excavator,mini excavator,garden ecavator
>>
Vegetable Pulp Press Machine Ginger Juicing Double Screw Cold Press Juicer
>>
Custom Lightweight Anti-Smashing Workmans Safety Shoes Anti-Puncture Breathable Steel Toe Safety Shoes
>>
Szgh Manufacturer Low Cost Combination CNC Lathe and Milling Machine China Horizontal CNC Metal Lathe Machine Mini Lathe CNC
>>
Factory supply Big Capacity Oil Pressing Filtering Machine /Commercial Stainless Steel Home Cold Pressed
>>
HT1850 Wholesale Popular Hand Cart Trolley Hand Truck, with 3.50-4 inch Pneumatic Wheel, Heavy Duty Steel
>>
NDIR Sensor CO2 Controller for Greenhouser and Hydroponics
>>
PE Film Washing Line / PE Film Recycling Machine
>>
Competitive Price Factory M6 DIN6927 Titanium Flange Nuts
>>
Hot Sale 90L CNG Seamless Steel Gas Cylinder 200bar for Vehicle Use with ISO11439 /ECR 110 Standard
>>
2024 Hot Sale Organza Jacquard Fabric Brocade Fabric French Tulle Lace Fabric for Curtain
>>
Animal Feed Processing Special Poutry Farm Cattle Mini Feed Pellet Machine
>>
New Professional Flat Soft Brush Contour Blusher Blush Foundation Makeup Cosmetics Tool Makeup Kabuki brushes Set Hot Selling
>>
ABS Minifigures building blocks toys,bricks and building for kid
>>
40 GSM Disposable Non Woven PP Coverall
>>
Advanced Oral Care Natural Dog teeth cleaning kit lfsponge wholesale
>>
2000w 940mm SK15 infrared heating lamp white plated infrared lamp
>>
Surgical Electric Drill with Multiple Payment Terms
>>
Megain CF232A 232A for Laser Jet PRO M203dw Compatible Toner Cartridge Drum
>>
Fuan Fangao 2022 Hot Selling Vibrating Heating Kneading Scraping Foot Massager 2 in 1 Shiatsu Back and Foot Massager Machine
