Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN50110-TV | 50 | 110 | 82 | 53.5 | – | – | 25 |
| 95 | – | – | 17.5 | – | – | 0.3 | 0.6 |
|
| 96 | 75 | 172,000 | 480,000 | 42,000 | 90,000 | 3,100 | 1,100 | 3.8 | 4,600 | 2,900 | 29.8 | 1 | 3.3 |
| ZARN50110-L-TV | 50 | 110 | – | – | 103 | 74.5 | 25 |
| 95 | 75 | 93 | 17.5 | 38.5 | 14 | 0.3 | 0.6 |
|
| 96 | 73 | 172,000 | 480,000 | 42,000 | 90,000 | 3,100 | 1,100 | 3.8 | 4,600 | 2,900 | 35.3 | 1 | 3.75 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Yamamoto Motorcycle Accessories Rear Hydraulic/Rubber/Gas/Spring-Air Shock Absorber for Honda Forza250
>>
Mini Excavator Sea Freight to Armenia Shipping Agent
>>
Aluminium entrance bi fold door interior door with high security and good quality
>>
High Quality Fully Automatic/Automation Vertical Fifo Compression/ Injection /Molding Rubber Injection Molding Machine for Rubber and Silicone Product
>>
Disposable Nonwoven 3ply Face Mask With Earloop For Hospital
>>
Disposable Non Woven Medical Bouffant Doctor Cap with Tie
>>
Electric children's scooter, two wheeled portable folding flash wheel, directly sold by the manufacturer of children's power scooters
>>
Ground Cutting Machine Lenmondog Ld-Q500 Fast Cutting Speed Super Rigid Box Frame Maximum Cutting Width of 500mm
>>
Wholesale High Quality MTB Mountain Bikes Variable Speed Bikes
>>
LIVTER Pneumatic Steel pipe Tube Pipe End Chamfering Machine
>>
HSS M42 Bimetal Band Saw Blade
>>
Food Grade Best Algae High Protein Spirulina Powder with Free Sample
>>
Manual Measuring Tool Tape Measure Retractable Steel Tape Measure with Roll
>>
Central air conditioning fuel pump, manual fuel pump, air conditioning fuel pump, fuel pump
>>
For Chevrolet Malibu 2016-2019 Rear Bumper Skin Traction Ring Manhole Cover 84559089 23352761
>>
China Supplier Amphibious Excavator Land and Water Excavator for Dredging
>>
0.5-10L Factory Price Dust-Proof Rubber and Plastic Mixing Kneader for Laboratory Test
>>
Wedding Decoration LC8822 24 6000K RGB 5V 12Vdc Led Strip Set Waterproof Led Strip Light For Living Room
>>
New Design Backpack Preschool Boys Girls Elementary Bookbag Lightweight Casual School Bag
>>
22943345 High quality aluminum car bumper front anti-collision bar FOR CHEVROLET MALIBU 2016-2018
