Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN2052-TV | 20 | 52 | 46 | 31 | – | – | 16 |
| 42 | – | – | 10 | – | – | 0.3 | 0.6 |
|
| 43 | 33 | 33,500 | 76,000 | 14,900 | 22,400 | 7,000 | 2,000 | 0.5 | 1,800 | 230 | 0.615 | 1 | 0.41 |
| ZARN2052-L-TV | 20 | 52 | – | – | 60 | 45 | 16 |
| 42 | 30 | 40 | 10 | 24 | 11 | 0.3 | 0.6 |
|
| 43 | 28 | 33,500 | 76,000 | 14,900 | 22,400 | 7,000 | 2,000 | 0.5 | 1,800 | 230 | 0.683 | 1 | 0.46 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
High Precision PA66/PBT+30GF Peek Auto Precision Terminal Connector Electric Auto Wireharness Housing Connector Plastic Injection Molding Mould
>>
Long Work Time Lamp High Lumen LED Solar Powered LED Street Light
>>
Disposable 1000ml Brown Kraft Paper Salad Food Bowl with Lid
>>
New Engine Water Pump for Mercedes Benz ML&GL Class W164 ML350 6422002201
>>
China 24 Cavity Plastic Injection Molding Blood Collection Tube Mold Mould Machine
>>
Heavy Duty Rubber Shipping Lifting Launching Inflatable Marine Airbag for Shipyards
>>
Automatic Paper Tag Knot Tying Machine (TL-LY8)
>>
Classic Luxury Men's Couple Watch Automatic Mechanical Movement Ladies Watch
>>
Freefall Inflatable Stunt Jumping Platform Air Bag Inflatable Cliff Jump
>>
Hole Tray Nursery Automatic Seeding Seeds Sowing Machine
>>
1stshine Ceiling Fan Factory OEM D. I. Y ABS Blades Energy Saving Smart Remote Ceiling Fan
>>
LIMELIGHT factory price clear kayak/transparent kayak/crystal kayak/crystal clear kayak/transparent clear kayak/clear bottom kayak/glass kayak
>>
Powder Coating/Paint Producing/Manufacturing/Production/Making High Speed Pre/Double Cone/Container Mixer
>>
808nm Diode Laser Hair Removal and Skin Rejuvenation Machine Price in Guangzhou Renlang
>>
Solar Water Heater Pressure Vessel Oil Tank Automatic Rolling Machine for Stainless Steel Aluminum
>>
Good Quality Grassland Field Fence Waving Machine
>>
CI858 3BSE018136R1
>>
Reverse osmosis membrane vessel 8040 reverse osmosis membrane shell FRP pressure vessel
>>
2 Wheel Cheap Electric Moped Bike with Pedals Electrica Ebike Scooter Electric Bike Bicycle
>>
Stainless Steel Salt Pepper Grain Feed Sugar Crusher Machine
