Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN4075-TV | 40 | 75 | 54 | 37 | – | – | 20 |
| 65 | – | – | 11 | – | – | 0.3 | 0.6 |
|
| 66 | 55 | 59,000 | 163,000 | 27,500 | 53,000 | 4,400 | 1,600 | 1 | 2,800 | 1,030 | 3.78 | 1 | 0.9 |
| ZARN4075-L-TV | 40 | 75 | – | – | 70 | 53 | 20 |
| 65 | 50 | 63 | 11 | 27 | 12 | 0.3 | 0.6 |
|
| 66 | 48 | 59,000 | 163,000 | 27,500 | 53,000 | 4,400 | 1,600 | 1 | 2,800 | 1,030 | 4.35 | 1 | 1 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Shampoo Bottle Injection Blowing Molding Machine From 100ml T O 500ml PE PP
>>
Horizontal Plow Blade Mixer/ High Speed Horizontal Ploughshear Mixer
>>
Hot Popular China Manufacturer Plastic pellet mixer batching machine for injection production
>>
Xk2130 CNC Gantry Type Milling Machine with Fixed Columns
>>
Promotion Gift 3D Pen Idrawing 3D ABS Filament Pen Yousu 3D Tech 3D Printing Pen 1.75mm Fla Filament Education Children 3D Smart Creation Pen
>>
Single Punch Tablet Pressing machine ,milk slice press machine with high quality
>>
EC Factory direct Anatomy laboratory equipment Anatomical system manufacturer
>>
Front Strut Element Front Axle Gas Pressure Shock Absorber fit for Mitsubishi Pajelo
>>
Car DVD Decorative Mounting Kit For 2004-2008 407 Radio Stereo Frame With Power Cable
>>
Accept Customer′s Logol Printed Bottles
>>
Pure Tungsten Metal Powder High Purity Tungsten Powder 99.9% Powder
>>
Slide Style Ultral Slim Mini USB Drive Metal Custom USB Flash Drive
>>
Hot sale CARBONIZED BAMBOO CHOPSTICK China
>>
Herbs Garlic Pepper Milling Machine Turmeric Masala Plastic Powder Grinder Machine
>>
Straight Metal Custom Laser Leather Black And Gold 3 in 1 High-end Gift Set Cigar Cutter
>>
Factory Supply 24 Hours Timer T3 R22 Domestic Air Conditioning
>>
Double torch automatic gas cutting machine
>>
New Excavator Bucket GP bucket for Komatsu PC210-10M0 Excavator
>>
Factory Supply Copper Wire Carton closing Staples 3515& 3518
>>
JOHNCOO 500pcs/bag 5/0-10/0 High Carbon Steel Fishing Crank Hook Blood Barbed Crank Hook for Soft Bait Lure Hook Fishing
