Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARF70160-TV | 70 | 160 | 82 | 51 | – | – | 22.5 | 12.5 | 115 | – | – | 17.5 | – | – | 0.3 | 0.6 | 6 | 133 | 116 | 100 | 201,000 | 630,000 | 56,000 | 119,000 | 2,400 | 800 | 4.8 | 5,800 | 6,000 | 62.2 | 1 | 5.2 |
| ZARF70160-L-TV | 70 | 160 | – | – | 103 | 72 | 22.5 | 12.5 | 115 | 100 | 115 | 17.5 | 38.5 | 16 | 0.3 | 0.6 | 6 | 133 | 116 | 98 | 201,000 | 630,000 | 56,000 | 119,000 | 2,400 | 800 | 4.8 | 5,800 | 6,000 | 77.3 | 1 | 5.95 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
100G-1Kg Packing Liquid Sachet Packing Automatic Bag Making Spices Paste Doypack Packaging Machine
>>
Decorticated Hemp Fiber Cleaning Line
>>
Draw Frame with Auto Leveller Nas System Model Jwf1366PRO Single Head Hot Selling Drawing Frame Machine
>>
2mm 4mm 7mm 13mm Teal Green Color Cut Edges Ribbon in Style Wedding Silk Ribbon on Plastic Spools
>>
Dog Canine Blood Typing Card for Accurate Pet Blood Test
>>
Art Drawing Color Mega Art Set 150 PCS Painting Creativity Set for Beginners and Young Artists
>>
Hotel key chain, hiking bag buckle multi-function key chain scoring accessories
>>
CR-V Go-Through Wood Chisel Set with Hardened Strike end For Woodworking Carving
>>
Seawater filter mesh fabric 30 micron dutch weave 316 filter mesh cloth
>>
High quality cheap price Outdoor waterproof windproof breathable jacket
>>
Hot Sale Stainless Steel Campfire Tripod Adjustable Chain Hanging Camping Cookware Set
>>
2/3/5/7 Layer Corrugated Cardboard Production Line Carton Box Making Machine
>>
Luxury Household Leisure Plastic Iron Dining Chair Modern Nordic Commerical Home Restaurant Hotel Cafe Waiting Reception Chair
>>
New Arrival PVC Artificial Marble Board Sheet Profile Extrusion Machine/PVC Imitate Marble Stone Production Line
>>
Simple Slitting Machine Tile Making Machinery Product
>>
Carbon steel investment casting hand operated meat mincer parts
>>
6ES7288-3AR04-0AA0SiemensSIMATIC S7-200 SMART module analog input SM AR04 RTD
>>
Nail produce line iron nail forming machine nail making machine
>>
8 Inch higth quality stainless steel gun shaped folding pocket colorful gun knife
>>
Factory Low MOQ Custom Logo Octopus Shape Curly Hair Detangler Wholesale Plastic 8 Rows Personalized Detangling Hair Brush
