Product Details
Product Description
Product Description
| Designation | Dimensions | Mounting dimensions | Basic load ratings | Limiting speeds | Bearing frictional torque
MRL
Nm | Rigidity axial
caL
N/µm | Tilting rigidity
ckL
Nm/ mrad | Mass moment of inertia3)
Mm
kg · cm2 | Axial runout6)
µm | Mass m =kg |
| axial | radial |
Da
max. | da
min. | dyn.Ca | stat. C0a | dyn.Cr | stat. C0r | nG oil | nG grease |
| d | D | H | H1 | H2 | H3 | C | C1 | D1 | D2 | D3 | B | B1 | B2 | r
min. | r1
min. | d1 | J | N | N | N | N | min–1 | min–1 |
| ZARN55115-TV | 55 | 115 | 82 | 53.5 | – | – | 25 |
| 100 | – | – | 17.5 | – | – | 0.3 | 0.6 |
|
| 101 | 85 | 177,000 | 500,000 | 44,000 | 98,000 | 2,900 | 1,000 | 4 | 4,900 | 3,600 | 36.1 | 1 | 3.5 |
| ZARN55115-L-TV | 55 | 115 | – | – | 103 | 74.5 | 25 |
| 100 | 80 | 98 | 17.5 | 38.5 | 14 | 0.3 | 0.6 |
|
| 101 | 78 | 177,000 | 500,000 | 44,000 | 98,000 | 2,900 | 1,000 | 4 | 4,900 | 3,600 | 43 | 1 | 4 |
Needle roller/axial cylindrical roller bearings (With fixing holes Without fixing holes)
Features
Needle roller/axial cylindrical roller bearings comprise an outer ring with radial and axial raceways, shaft locating washers, an inner ring, a radial needle roller and cage assembly and axial cylindrical roller
and cage assemblies. The bearings are available in versions with or without fixing holes.
Radial and axial load carrying capacity
In addition to radial forces, the bearings can also support axial forces from both directions and tilting moments.
Preload and internal clearance
The outer ring, inner ring and axial cages are matched to each other such that the bearing is axially clearance-free after preloading by means of an theprecision locknut. The radial internal clearance conforms to Group 2 in accordance with ISO 5753-1 .
Bearings for screw mounting
Needle roller/axial cylindrical roller bearings ZARF(L) have holes in the outer ring. These are used for screw mounting directly on the adjacent construction or in a radial locating bore Figure 1.
Due to screw mounting of the outer ring, the cover that would otherwise be required and the matching work can therefore be dispensed with. The bearings are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
With seal carrier assembly
In the interests of a simpler design, a seal carrier assembly DRS, Figure 1 is recommended. The seal carrier assembly is centred on the outer ring and seals the bearing against outside influences.
ZARF..-L
Figure 1 Stepped shaft locating washer with sealing ring
1.Seal carrier assembly DRS
2.Locknut AM
3. Stepped shaft locating washer extended on one side
4. Rotary shaft seal DIN 3760-..-NBR
With stepped shaft locating washer
ZARF..-L has a stepped shaft locating washer extended on one side, Figure 1. These series are used in preference where the shaft locating washers are not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Heavy series
ZARF(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Bearings not for screw mounting
Bearings ZARN(L) are mounted in a housing bore and the outer ring is located using a cover, Figure 2. They are preloaded against the shaft shoulder by means of a locknut AM or ZM(A).
ZARN
Figure 2
Bearing outer ring located using cover
With stepped shaft locating washer
ZARN..-L has a stepped shaft locating washer extended on one side, Figure 3. This series is used in preference where the shaft locating washer is not adequately supported axially by the shaft shoulder or the bearing unit cannot be sealed on the outside surface of the normal shaft locating washer due to space conditions in the adjacent construction.
Figure 3
ZARN..-L
1.Stepped shaft locating washer extended on one side
2.Rotary shaft seal DIN 3760
Stepped shaft locating washer with sealing ring
Heavy series
ZARN(L) is also available in a heavy series. This series has a larger cross-section for the same shaft diameter and therefore higher basic load ratings.
Operating temperature
The bearings are suitable for temperatures from –30 °C to +120 °C.
Suffixes Suffixes for available designs, see table.
Available designs
>>
Two Wheel Mini Farm Tractor 101 Rotary Tiller
>>
EU/JP/KR/UK/US Useful Standard Jewelry Measuring Tool Rings Size Metal Finger Ring Sizer Measure Gauge
>>
80inches 7gg Kailong Three System Flat Knitting Machine for Sweater with Dark Blue
>>
Simple Wardrobe Closet Organizer Coat Hanger Freestanding Clothes Garment Stand 360 Degree Wheels
>>
Compact and Powerful Hammer Crusher for All Industry Needs Hammer Crusher
>>
Xz Factory Hot Selling Four Spindle Faucet Making Tapping Machine Electric Drill Machine Faucet Machining Centre
>>
Reliable Electric Tricycle for Cargo with Enhanced Speed and Range
>>
High Precision Equipment RoHS Certification Automatic Mdy0642 Machine Metal Lathe
>>
40# 220V 100W AC Permanent Magnet Synchronous Servo Motor Without Brake
>>
Digital Ultrasonic Cleaners for Industrial Jewelry Medical Instrument Laboratory
>>
High Quality Foam Sponge Carton CNC Film Fabric Full Automatic Cutting Machine
>>
Automatic Bottle Filling Line Perfume Body Spray Bottle Liquid Filling Machine For 50ml 100ml
>>
EVA Colorful Indoor Kids Educational Splicing Blocks Toy
>>
OEM ODM PTFE PFA Coaed Disc Wcb Bronze BS Standard Control Butterfly PVC Wafer Check Valve
>>
wholesale diamond hair ornaments
>>
Custom Industrial Sewing Table for Heavy-Duty Garment Production Efficiency
>>
cheap price electric hookah charcoal flavour
>>
Micro tiller, small ripper, rotary ridge Garden Easy weeding Mini Hand ditching diesel gasoline engine multi-function
>>
Low MOQ Custom Stuffed Anime Figure Plush Dolls Cotton Doll Customize
>>
Chinese Stained Glass Supplier Custom Size High Quality Transparent Flat Colored Art Church Glass Panels Wholesale Price
